Help required pleeaasse
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 148
- Joined: 16 May 2018, 08:12
- 80-90 Mem No: 0
- Location: Cycle City on the Cam
Help required pleeaasse
Hi all, I have an 88 E reg with a 1.9 DG in it. Prob is the 2 hoses that run around the back of the engine bay the big ones. One has a 10mm pipe off it that connects to a metal pipe with a junction joint that includes an electrical connection. The other one also has 10mm take off pipe with broken bleed valve of some type on the end of it. I need to bleed the system but the valve don't turn. None of this looks anything like what's in ta book!
Any body know?
Any body know?
- ajsimmo
- Trader
- Posts: 2701
- Joined: 23 Mar 2009, 14:06
- 80-90 Mem No: 6542
- Location: Isle of Arran
- Contact:
Re: Help required pleeaasse
That's weird. It appears you've got a late van with an early cooling system. Pics might help us get to the bottom of the conundrum.
Sent from my ONEPLUS A3003 using Tapatalk
Sent from my ONEPLUS A3003 using Tapatalk
The Campershack - (website paused)
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
- Mocki
- Membership Admin
- Posts: 16966
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: Help required pleeaasse
Yes sounds like the muppettry has been here before you, and you have a late van with early cooling system .... if that’s the case ,
Relax, for that bleed valve will be fine not opening , many early system vans now don’t even have that valve, just straight joiner to the metal crossover pipe and a bung in the other one , or a "Y" joining all .
You will be able to bleed fine as it is as long as it’s not stuck open.
Just raise the revs to about 2000 , top the header tank up to the brim , and open the rad bleed bolt , and keep pouring water in the header tank so it’s level is always full to overflowing .
You do need the heater on hot from the start til the end , and when you are long longer getting air from the rad, close the bleed bolt , top the header tank up to the brim put the cap on, then reduce the revs to idle . Give it 2 mins and switch off , go make and drink a brew . Come back in ten mins and open the rad bleed valve slowly and if coolant comes out but not air it’s pretty much bled .
Relax, for that bleed valve will be fine not opening , many early system vans now don’t even have that valve, just straight joiner to the metal crossover pipe and a bung in the other one , or a "Y" joining all .
You will be able to bleed fine as it is as long as it’s not stuck open.
Just raise the revs to about 2000 , top the header tank up to the brim , and open the rad bleed bolt , and keep pouring water in the header tank so it’s level is always full to overflowing .
You do need the heater on hot from the start til the end , and when you are long longer getting air from the rad, close the bleed bolt , top the header tank up to the brim put the cap on, then reduce the revs to idle . Give it 2 mins and switch off , go make and drink a brew . Come back in ten mins and open the rad bleed valve slowly and if coolant comes out but not air it’s pretty much bled .
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
-
- Registered user
- Posts: 148
- Joined: 16 May 2018, 08:12
- 80-90 Mem No: 0
- Location: Cycle City on the Cam
Help required pleeaasse
Mocki wrote:Yes sounds like the muppettry has been here before you, and you have a late van with early cooling system .... if that’s the case ,
Relax, for that bleed valve will be fine not opening , many early system vans now don’t even have that valve, just straight joiner to the metal crossover pipe and a bung in the other one , or a "Y" joining all .
You will be able to bleed fine as it is as long as it’s not stuck open.
Just raise the revs to about 2000 , top the header tank up to the brim , and open the rad bleed bolt , and keep pouring water in the header tank so it’s level is always full to overflowing .
You do need the heater on hot from the start til the end , and when you are long longer getting air from the rad, close the bleed bolt , top the header tank up to the brim put the cap on, then reduce the revs to idle . Give it 2 mins and switch off , go make and drink a brew . Come back in ten mins and open the rad bleed valve slowly and if coolant comes out but not air it’s pretty much bled .
Thanks Steve, Sounds likely as the previous owner was a bit of lets say cheapskate being polite
Now found another problem the metal pipe along the top is leaking where the mounting bracket is attached to it. Thing is I can't see one on any of the parts drawings on JK BWerks or VW H????
- Mocki
- Membership Admin
- Posts: 16966
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: Help required pleeaasse
You won’t get that crossover pipe new, it’s obsolete
Mick at NWVW May be able to help , or McGill maybe .
Make sure you get the correct one for your carb, there is a difference between DG and DF on that pipe
Sent from my iPad using Tapatalk
Mick at NWVW May be able to help , or McGill maybe .
Make sure you get the correct one for your carb, there is a difference between DG and DF on that pipe
Sent from my iPad using Tapatalk
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
-
- Registered user
- Posts: 148
- Joined: 16 May 2018, 08:12
- 80-90 Mem No: 0
- Location: Cycle City on the Cam
Re: Help required pleeaasse
So do we have any numbers for these guys?
I was thinking maybe cut through the pipe where the hole is and sleeve it with a section of rubber hose. Any thoughts any one?
I know the rest doesn't look wonderful!
I was thinking maybe cut through the pipe where the hole is and sleeve it with a section of rubber hose. Any thoughts any one?
I know the rest doesn't look wonderful!
- Mocki
- Membership Admin
- Posts: 16966
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: Help required pleeaasse
Mick , NWVW number is 07968 367046
You might be able to cut and sleeve it , depending on if you have enough good unpitted straight metal to get a good tight fit on each end .
You might be able to cut and sleeve it , depending on if you have enough good unpitted straight metal to get a good tight fit on each end .
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
-
- Registered user
- Posts: 148
- Joined: 16 May 2018, 08:12
- 80-90 Mem No: 0
- Location: Cycle City on the Cam
Re: Help required pleeaasse
Thanks Steve.
By the way how should all those pipes join together then on latter ones?
Also Steve
By the way how should all those pipes join together then on latter ones?
Also Steve
- Mocki
- Membership Admin
- Posts: 16966
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: Help required pleeaasse
The early cooling system is completely different to the late
This is what you have
This is the late system
Sent from my iPad using Tapatalk
This is what you have
This is the late system
Sent from my iPad using Tapatalk
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
-
- Registered user
- Posts: 4569
- Joined: 15 Oct 2010, 21:55
- 80-90 Mem No: 8927
- Location: London
Re: Help required pleeaasse
I always thought that on the late system the big pipe behind the thermostat took coolant to the rad. On this it appears the flow is coming from the rad to the thermostat?
Honorary "Dave"
- Mocki
- Membership Admin
- Posts: 16966
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: Help required pleeaasse
yes, the thermostat is on the other end of the head , and the coolant that has been cooled comes from the rad back
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
-
- Registered user
- Posts: 148
- Joined: 16 May 2018, 08:12
- 80-90 Mem No: 0
- Location: Cycle City on the Cam
Re: Help required pleeaasse
Either way they both look very complicated!
Just going to go and see if I can remove the top cross over pipe to inspect it. I'll report back later.
Just going to go and see if I can remove the top cross over pipe to inspect it. I'll report back later.
-
- Registered user
- Posts: 148
- Joined: 16 May 2018, 08:12
- 80-90 Mem No: 0
- Location: Cycle City on the Cam
Re: Help required pleeaasse
Well got it off this afternoon. It don't look that good so I gave Mick a ring and he says to ring him Saturday Morning and he'll have a look but he knows he has some. So thanks a bunch Steve looks like you've saved another camper! Wife is threatening to list it on the bay site!
- Mocki
- Membership Admin
- Posts: 16966
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: Help required pleeaasse
Good, pleased to have been some help...
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
-
- Registered user
- Posts: 4569
- Joined: 15 Oct 2010, 21:55
- 80-90 Mem No: 8927
- Location: London
Re: Help required pleeaasse
That's interesting. When the head gasket failed, I noticed that pipe didn't get hot and thought it was the thermostat. Looking at the diagram it must have been a blockage in the rad. I'll need to have another lookMocki wrote:yes, the thermostat is on the other end of the head , and the coolant that has been cooled comes from the rad back
Honorary "Dave"