WBXmayo

Big lumps of metals and spanners. Including servicing and fluids.

Moderators: User administrators, Moderators

300CE
Registered user
Posts: 2531
Joined: 16 Aug 2012, 13:05
80-90 Mem No: 12017
Location: Sidcup, Kent

Re: WBXmayo

Post by 300CE »

itchyfeet wrote:That or I weld a few old cases together and make a V12 :D

Now that I’d like to see!
'86 DG, Weber Carb

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

Dug them all out, the good news is I have some better that mayo engine had.

Going to hone them, clean the seal recesses and then decide which to use.

ImageP1080932 by Paul_Barr, on Flickr

Some hone up like this, I don't really know if it's a problem of not

ImageP1080931 by Paul_Barr, on Flickr

Its a shame a few that are really good inside have damage to the compression sealing surface presumably by some cack handed engine rebuilder in the past, I don't think I would risk it.

ImageP1050648 by Paul_Barr, on Flickr

Never seen a cracked one before, this had this piston

ImageP1080930 by Paul_Barr, on Flickr

Image20170907_174246 by Paul_Barr, on Flickr

Got a scored one from a circlip that broke free, I think somebody put it back like this because the circlip isn't missing anymore!!!

ImageP1080935 by Paul_Barr, on Flickr

also as well as some that have just got pitted from rust
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

Honed them all now , removed all old orings, wire brushed the top seal and used wet and dry 600 grit on the sealing surface to clean it up.
Honed with brake fluid ( because you want to cut not slide) but brake fluid is hydroscopic so they must be oiled after or they soon rust.

ImageP1080938 by Paul_Barr, on Flickr

Image20171213_183201 by Paul_Barr, on Flickr

It's not until you hone that you see the real condition, these are from mayo engine, it was probably only driven 10 miles with mayo in it but you can really see the damage done.

ImageP1080940 by Paul_Barr, on Flickr

ImageP1080939 by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

300CE
Registered user
Posts: 2531
Joined: 16 Aug 2012, 13:05
80-90 Mem No: 12017
Location: Sidcup, Kent

Re: WBXmayo

Post by 300CE »

Are those really scrap now Paul or can something be done to rectify?
'86 DG, Weber Carb

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

300CE wrote:Are those really scrap now Paul or can something be done to rectify?

I'm sure you could refit them and I'm sure budget engine rebuilders do, engine will run fine, its not a race engine but it has to be loosing a bit of compression.
the scratches are not deep but honing really showes up inperfections.

As this is a Higher compression DJ I'd rather pick the best I have.
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

After another couple of hours honing and inspecting I have four winners.
Barrels
94.03
94.04
94.05
94.04

So paring with pistons we are all well under the 0.2mm wear limit :D

No1 93.95 / 94.04 = 0.09
No2 93.93 / 94.04 = 0.11
No3 93.90 /94.03 = 0.13
No4 93.95 /94.05 = 0.10

I have two other DJ pistons I'm going to dig out and see if I can improve on the 93.90 one.

closer tolerances mean less ring gap too so better compression.

ImageP1080944 by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

300CE
Registered user
Posts: 2531
Joined: 16 Aug 2012, 13:05
80-90 Mem No: 12017
Location: Sidcup, Kent

Re: WBXmayo

Post by 300CE »

itchyfeet wrote:
300CE wrote:Are those really scrap now Paul or can something be done to rectify?

I'm sure you could refit them and I'm sure budget engine rebuilders do, engine will run fine, its not a race engine but it has to be loosing a bit of compression.
the scratches are not deep but honing really showes up inperfections.

As this is a Higher compression DJ I'd rather pick the best I have.

:ok :ok
'86 DG, Weber Carb

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

Dug out my spare DJ pistons and they are both a different weight group, one is 0.02mm bigger but it's not worth swapping it.

ImageP1090018 by Paul_Barr, on Flickr

found a gudgeon pin that was more like the right weight

ImageP1090020 by Paul_Barr, on Flickr

checked the con rods just in case somebody swapped a gudgeon pin to offset a heavy con rod but no they are all within a couple of grams

ImageP1090021 by Paul_Barr, on Flickr

These are stretch bolts ( note long threads) and onetime use so I have removed a set of non stretch ( short threads) from an early engine that I'm going to fit.

ImageP1090023 by Paul_Barr, on Flickr

reamed the burrs so that the pins slide in

ImageP1090024 by Paul_Barr, on Flickr

Cleaned up the pistons with wet and dry, paraffin, carb cleaner and a toothbrush ready for ring measuring/checking/fitting

ImageP1090027 by Paul_Barr, on Flickr
Last edited by itchyfeet on 17 Dec 2017, 21:39, edited 1 time in total.
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
937carrera
Registered user
Posts: 3599
Joined: 05 Apr 2015, 19:29
80-90 Mem No: 16333
Location: N Yorks.

Re: WBXmayo

Post by 937carrera »

Are you going to remove some material to balance the piston weights up - not necessary, but you seem to be taking quite a lot of care?
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

937carrera wrote:Are you going to remove some material to balance the piston weights up - not necessary, but you seem to be taking quite a lot of care?

Nope, 10grams is VW spec I'm well under that, it's not a race engine but I try to keep inside VW spec.
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

checked little end bearings with the piston pins, this isn't in the VW manual there seem to be no specs of wear limits I can find.

I have read a general rule of thumb is it should not fall out when oiled and pushed into the con rod and held vertically, there should be no play that can be felt.

This says to me these rods have been changed when it was last rebuilt or the bushes were replaced and reamed, most I have seen removed from engines pins fall out and you can feel play.

ImageP1090041 by Paul_Barr, on Flickr

swapped the bolts over to standard, the nuts are different on standard too they have a reduced contact area

ImageP1090042 by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

cam adapters arrived today from USA
they spent more time getting from UK to me than USA to UK
When anything arrives from USA it has to go through customs then you get sent a bill for VAT + import duty with a handling fee ( about 12 quid handling fee for parcel force) once you pay it gets delivered.

I bought a couple for other members on here also to get the price down sharing the postage.

ImageP1090044 by Paul_Barr, on Flickr

Unfortunately Royal mail took 3 weeks to deliver my old cam to Newman cams so they have only just got it so no cam for a few more weeks because they are on shutdown next week.

I still have loads of prep to do so next is the heads.

These are two used AMC heads that I bought and bartered, the valves are not VW and so they are going to get swapped out with valves from some old scrap heads I have...assuming I find nothing else wrong with them.

ImageP1090046 by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

Just got this extract from type 4 manual for little end clearances, type 4 being the same pin size...interesting

ImageType 4 little end spec by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

And another thing worth noting , there is a plugged drilling to the high pressure oil gallery between cylinder 3&4 into the water jacket if you have your engine apart check it, if it fails you get oil in the water as the third pic shows.

hard to see usually because the studs hide it but in this pic with a broken stud it becomes very clear, it a drilling to get to the tappet/low pressure oil switch seen on the second picture

ImageP1030802 by Paul_Barr, on Flickr

ImageP1030798 by Paul_Barr, on Flickr

Imagefailed plug to oil gallery by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXmayo

Post by itchyfeet »

Ohhh look what turned up today :D

ImageP1090159 by Paul_Barr, on Flickr

I'm going to try and measure it and compare with the old cam so I made a jig up ( bolts are turned to a cone)

ImageP1090163 by Paul_Barr, on Flickr

it's a lot harder than it looks, it's frying my brain, I'm trying to get numbers that look like this but they don't yet. Cam turns anticlockwise as crank turns clockwise and zero is I assume the mark on the cam gear :? I must have the scale wrong

I'm also wondering if the old cam is even a DJ because it doesn't look the same as CJH's graph :?

Image
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Post Reply