Replacing the dashboard plastic PCB

An alchemy of sparks, copper wire and earth

Moderators: User administrators, Moderators

Post Reply
MidLifeCrisis
Registered user
Posts: 566
Joined: 20 Nov 2011, 19:07
80-90 Mem No: 10519
Location: Bagshot, Surrey

Replacing the dashboard plastic PCB

Post by MidLifeCrisis »

I just replaced the plastic PCB on my dashboard broadly following Covkid's instuctions in the Wiki;
http://wiki.club8090.co.uk/index.php/VW ... _connector

I thought the PCB layout that I used might be of use/interest to others.

Note that my dash is the simplest version out there - petrol, no rev counter, no clock (although I did include the clock wiring). I also added an additional light into the dash as a spare for the future.

Image

Just to clarify this is a view from the component (top) side of the veroboard (even though you can see the vertical tracks that would be on the underside - imagine that the board is slightly transparent).
The LED were mounted on the back of the Veroboard (i.e. on the track side, facing downwards).
Each wire from the connector arrives at the board on the bottom row (shown by the wire names on the pic)
The wires to the fuel gauge/coolant temp etc then come off the board on wires from the small black circles on the second from bottom row)
The wires to the three illumination lights come off the board on the 6 x black circles on the bottom right of the board.
The red dots are where the tracks are cut.
Note that I used an LED for the High Beam so that has a different resistor value to the original circuit.

SP1 is my spare LED that is lit when the SP1 wire is grounded - just got to think of a use for this now.

For others trying this, the most useful information on here is probably the spacing of the mounting holes and the LEDS. (Note for reference that the component holes on the veroboard are 0.1" apart) You can design the board however you like but those elements need to be spaced as shown so that they will all mount correctly into the dash.
Also its worth mentioning that the components are mounted so that they do not interfere with the various bits that stick up from the LED mounting section of the dash.

This is how it looks in the end;
Image
(Note that the illumination lights are not connected in this pic - but the connectors can be seen on the bottom right of the board)

It seems to work really well - just need to do something about the blinding brightness of the blue LED for the High Beam.

Also finally for completeness - here is my diagram that I created by tracing the wire on the original plastic PCB that might help if you are thinking of doing something similar.

Image
1987 Westfalia Van, Petrol 2.0 AGG

User avatar
icosahedron
Registered user
Posts: 40
Joined: 12 Aug 2010, 21:12
80-90 Mem No: 8620
Location: UK

Re: Replacing the dashboard plastic PCB

Post by icosahedron »

:ok Thanks for sharing.

User avatar
1664
Registered user
Posts: 8747
Joined: 30 Mar 2006, 15:20
80-90 Mem No: 3299
Location: Coventry Member

Re: Replacing the dashboard plastic PCB

Post by 1664 »

:ok
Vorsprung Durch Technik my ar$e!

User avatar
ghost123uk
Registered user
Posts: 6857
Joined: 10 Mar 2006, 10:15
80-90 Mem No: 2585
Location: John in Malpas, in the very S. W. part of Cheshire.
Contact:

Re: Replacing the dashboard plastic PCB

Post by ghost123uk »

Bliddy heck, that's good presentation :ok

What software did you use to do both the block diagram and the circuit diagram ?
Got a new van, but it's a 165bhp T4 [shock horror] Accurate LPG Station map here

MidLifeCrisis
Registered user
Posts: 566
Joined: 20 Nov 2011, 19:07
80-90 Mem No: 10519
Location: Bagshot, Surrey

Re: Replacing the dashboard plastic PCB

Post by MidLifeCrisis »

ghost123uk wrote:Bliddy heck, that's good presentation :ok

What software did you use to do both the block diagram and the circuit diagram ?

Thanks
Block diagram was just done in powerpoint.
The circuit diagram was done on something called 'DIY Layout Creator' that I found on the interweb - http://www.diylc.org
1987 Westfalia Van, Petrol 2.0 AGG

User avatar
ghost123uk
Registered user
Posts: 6857
Joined: 10 Mar 2006, 10:15
80-90 Mem No: 2585
Location: John in Malpas, in the very S. W. part of Cheshire.
Contact:

Re: Replacing the dashboard plastic PCB

Post by ghost123uk »

MidLifeCrisis wrote: Block diagram was just done in powerpoint.

Flip, that must have taken you ages I would have thought, really well done I say :ok

MidLifeCrisis wrote: The circuit diagram was done on something called 'DIY Layout Creator' that I found on the interweb - http://www.diylc.org

I'll have a go at that :ok

Got to be a wiki candidate this has, Harry, where are you :wink: (is it just HarryMann that does the main wiki entries ?)
Got a new van, but it's a 165bhp T4 [shock horror] Accurate LPG Station map here

User avatar
Aidan
Trader
Posts: 6522
Joined: 11 Oct 2005, 19:21
80-90 Mem No: 742
Location: Llanfyllin, mid Wales : )
Contact:

Re: Replacing the dashboard plastic PCB

Post by Aidan »

Nice work, many thanks for sharing :ok

User avatar
CovKid
Trader
Posts: 8409
Joined: 30 Apr 2006, 13:19
80-90 Mem No: 3529
Location: Ralph - Coventry (Retired)
Contact:

Re: Replacing the dashboard plastic PCB

Post by CovKid »

Added to my WIKI on hardwiring. Worth adding LED sockets as I did - saves messing if one needs replacing/swapping later. The blue LED can be dipped in black paint. Works a treat. Either that or feed it into original cap that was on bulb (if you can still find it). As I noted once before, the reason VW used a white bulb and a dark blue plastic cap was because blue LEDs hadn't been invented. You can get the original bulb ofcourse but then why would you given the longer lifespan of LEDs.
Last edited by CovKid on 14 Feb 2014, 16:59, edited 3 times in total.
Roller paint your camper at home: http://roller.epizy.com/55554/" onclick="window.open(this.href);return false; for MP4 download.

MidLifeCrisis
Registered user
Posts: 566
Joined: 20 Nov 2011, 19:07
80-90 Mem No: 10519
Location: Bagshot, Surrey

Re: Replacing the dashboard plastic PCB

Post by MidLifeCrisis »

CovKid wrote:Worth adding LED sockets as I did - saves messing if one needs replacing later.
Yeah - I tried using some sockets that I had but couldn't get the LED legs to stick in them properly.
So in the end I gave in and soldered them figuring that LEDs last for ages and it wouldn't be the worst job in the world to unsolder and stick in a new one in I had to ...
1987 Westfalia Van, Petrol 2.0 AGG

User avatar
keytouch
Registered user
Posts: 952
Joined: 17 Oct 2007, 22:31
80-90 Mem No: 4484
Location: West Somerset

Re: Replacing the dashboard plastic PCB

Post by keytouch »

CovKid wrote:Worth adding LED sockets as I did.

I'm in the middle of doing this project but am struggling to source sockets for the LEDs. Are you able to point me in the right direction?
Jonathan

A Camper called Wanda
1983 A reg Bilbo Marlfield conversion, 1900 Diesel 1Y engine

User avatar
CovKid
Trader
Posts: 8409
Joined: 30 Apr 2006, 13:19
80-90 Mem No: 3529
Location: Ralph - Coventry (Retired)
Contact:

Re: Replacing the dashboard plastic PCB

Post by CovKid »

Well, if memory serves me right, they're not specifically for LEDs but are just 2-pin veroboard sockets. Maplins do them.
Roller paint your camper at home: http://roller.epizy.com/55554/" onclick="window.open(this.href);return false; for MP4 download.

poshbuggers
Registered user
Posts: 1352
Joined: 23 Oct 2005, 19:15
80-90 Mem No: 0
Location: Nottinghamshire

Re: Replacing the dashboard plastic PCB

Post by poshbuggers »

GoWesty now sell a kit too.

Admittedly it's costly but better than risking buying another duff one. Plug and play too.

http://www.gowesty.com/ec_view_details. ... parent_id=

Nice to see solutions to a problem that seems to be creeping up on us all as these vans get older.

'90 Syncro Hightop. Ex-BUPA/Rowan ambulance with 2.0L GTI power and some curious windows.
)

User avatar
keytouch
Registered user
Posts: 952
Joined: 17 Oct 2007, 22:31
80-90 Mem No: 4484
Location: West Somerset

Re: Replacing the dashboard plastic PCB

Post by keytouch »

poshbuggers wrote:GoWesty now sell a kit too.

Admittedly it's costly but better than risking buying another duff one. Plug and play too.

http://www.gowesty.com/ec_view_details. ... parent_id=

Nice to see solutions to a problem that seems to be creeping up on us all as these vans get older.
Ouch that's a premium price
Jonathan

A Camper called Wanda
1983 A reg Bilbo Marlfield conversion, 1900 Diesel 1Y engine

User avatar
MattBW
Registered user
Posts: 764
Joined: 11 Sep 2012, 10:43
80-90 Mem No: 11790

Re: Replacing the dashboard plastic PCB

Post by MattBW »

Any idea if the diesel cluster and petrol are basically the same? Mine is 85 and has no rev counter, no clock, just speedo, fuel and temp really.

Maybe its time to learn some soldering skills ;)
1985 1.9TD AAZ -Starlight Interior
2015 California Beach

pirate-pete
Registered user
Posts: 232
Joined: 01 Nov 2009, 18:49
80-90 Mem No: 7945
Location: London

Re: Replacing the dashboard plastic PCB

Post by pirate-pete »

MattBW wrote:Any idea if the diesel cluster and petrol are basically the same? Mine is 85 and has no rev counter, no clock, just speedo, fuel and temp really.

Maybe its time to learn some soldering skills ;)

Basically the same yes but some slight differences as diesel will also have glow plug led. I know on the early ones without clock the has the clock tracks and terminals - just no clock to connect them too.
1983 Westy Joker HighTop, 1Z TDI Conversion

Post Reply