Speedo Bounce
Moderators: User administrators, Moderators
- Oldiebut goodie
- Registered user
- Posts: 7294
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: Speedo Bounce
How are you going to drive the cable if you grind off enough to pass through the outer?
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
-
- Registered user
- Posts: 293
- Joined: 04 Sep 2012, 21:25
- 80-90 Mem No: 11532
- Location: Wiltshire
Re: Speedo Bounce
Without looking I assumed it was like a ring crimped over the cable and you could carefully cut it off like taking insulation off a cable? Leaving the drive cable completely intact, I can see how it seemed I was saying chop the end off the cable, haha.
Greta: 85’ LHD 2.5L Subaru 14in Syncro
http://forum.club8090.co.uk/viewtopic.php?t=165773
http://forum.club8090.co.uk/viewtopic.php?t=165773
- Oldiebut goodie
- Registered user
- Posts: 7294
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: Speedo Bounce
Look back a couple of pages - I Feet has posted pics of the grease cap ends.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
-
- Registered user
- Posts: 293
- Joined: 04 Sep 2012, 21:25
- 80-90 Mem No: 11532
- Location: Wiltshire
Re: Speedo Bounce
Got it, I see what you mean. I would stick one end in a drill then put blobs of grease on with a lollipop sticker/wooden spreader and let the spiral draw the grease up like an Archimedes screw.
Years ago we used to work on generator sets that had a fan drive cable like a giant version of that speedo cable, we had to remove the inner every 12months to grease it or it would bind and unwind in the sheath, made a right mess.
Years ago we used to work on generator sets that had a fan drive cable like a giant version of that speedo cable, we had to remove the inner every 12months to grease it or it would bind and unwind in the sheath, made a right mess.
Greta: 85’ LHD 2.5L Subaru 14in Syncro
http://forum.club8090.co.uk/viewtopic.php?t=165773
http://forum.club8090.co.uk/viewtopic.php?t=165773
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: Speedo Bounce
I think someone is going to have to get destructive.
By that I mean chopping one end off, probably the wheel end, and withdrawing the inner cable for inspection. It does mean sacrificing one or two Gemo cables, but they're no good anyway ?
It'll still be possible to test with a drill, using any variety of lubricants if desired, just not fit to a van again.
Alternatively arrange for return to supplier for their R & D evaluation
By that I mean chopping one end off, probably the wheel end, and withdrawing the inner cable for inspection. It does mean sacrificing one or two Gemo cables, but they're no good anyway ?
It'll still be possible to test with a drill, using any variety of lubricants if desired, just not fit to a van again.
Alternatively arrange for return to supplier for their R & D evaluation
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Speedo Bounce
It was said early on, grease not oil
I'm wondering if the act of oiling has been the cause not the cure.
If they were greased at the factory and you add oil before fitting you wash the grease out, oil clearly does not last.
anyway this VW cable was fine after i oiled it, just a small bounce but no noise so it must be possible to lube it with grease and if it laost longer it may be the solution.
The noise appears to be resonance because it starts suddenly often after going over a bump, deffo coming from the cable becuse if i give it a reach around while driving I can feel it and just stop it by re positioning the cable.
Today I stopped off at tool station on my way home
P1100740 by Paul_Barr, on Flickr
first attempt didn't work because the inner sealed it off so I added a washer with a cut and this did the trick allowing the grease past into the outer
Dunno how much i got in but after a lot of pumping I got tired and had to stop, it never came out the top but I think a better spacer may do it.
Took it for a test drive and much better no noise and minimal bounce
Only time will tell
P1100739 by Paul_Barr, on Flickr
I'm wondering if the act of oiling has been the cause not the cure.
If they were greased at the factory and you add oil before fitting you wash the grease out, oil clearly does not last.
anyway this VW cable was fine after i oiled it, just a small bounce but no noise so it must be possible to lube it with grease and if it laost longer it may be the solution.
The noise appears to be resonance because it starts suddenly often after going over a bump, deffo coming from the cable becuse if i give it a reach around while driving I can feel it and just stop it by re positioning the cable.
Today I stopped off at tool station on my way home
P1100740 by Paul_Barr, on Flickr
first attempt didn't work because the inner sealed it off so I added a washer with a cut and this did the trick allowing the grease past into the outer
Dunno how much i got in but after a lot of pumping I got tired and had to stop, it never came out the top but I think a better spacer may do it.
Took it for a test drive and much better no noise and minimal bounce
Only time will tell
P1100739 by Paul_Barr, on Flickr
Re: Speedo Bounce
Now that is so simple
well done itchy
Just make sure no grease gets into speedo as it will I think mess it up
well done itchy
Just make sure no grease gets into speedo as it will I think mess it up
____________________________________________
84 CaravelleGL 1.9 DG WBX Bronze Beige Metallic auto
84 CaravelleGL 1.9 DG WBX Bronze Beige Metallic auto
-
- Registered user
- Posts: 293
- Joined: 04 Sep 2012, 21:25
- 80-90 Mem No: 11532
- Location: Wiltshire
Re: Speedo Bounce
great job, 10/10 for ingenuity
Greta: 85’ LHD 2.5L Subaru 14in Syncro
http://forum.club8090.co.uk/viewtopic.php?t=165773
http://forum.club8090.co.uk/viewtopic.php?t=165773
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Speedo Bounce
pop top.VW cable is better after grease but still noisy at times.
I stole the VW no bounce cable from the tin top and fitted it to the pop top today ( greased it first)
only did a 20 min test drive but looks good sounds good so probably not a speedo issue but a cable issue
tested the pop top VW cable thats noisy with a batt drill and you can feel the vibration
going to try pumping grease down from speedo end to see what happens.
I stole the VW no bounce cable from the tin top and fitted it to the pop top today ( greased it first)
only did a 20 min test drive but looks good sounds good so probably not a speedo issue but a cable issue
tested the pop top VW cable thats noisy with a batt drill and you can feel the vibration
going to try pumping grease down from speedo end to see what happens.
- Oldiebut goodie
- Registered user
- Posts: 7294
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: Speedo Bounce
I am thinking back to when my cable broke - it was soon after it exited the wheel area which leads me to believe that this is where there is strong contact between inner and outer. Is this the common failure point amongst those that have had failure? It's a pity that I didn't think more about the point of failure and the reason at the time so that there is more info on the subject.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Speedo Bounce
I'm tempted to buy a new gemo and pump grease in.
maybe that's all that's needed.
maybe that's all that's needed.
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Speedo Bounce
pumped some grease in top end today and refitted it ( in the rain ) had to hold the pipes together while pumping
tested it with drill first and seems better worse when inner is out of cable at hub so pushed it hard into hub
as you can see from the different colours top and bottom this cable has an outer joined in the middle dunno why
dunno how much grease I got in but the spiral will pull it down over time I think.
test driver later
20180826_112640 by Paul_Barr, on Flickr
tested it with drill first and seems better worse when inner is out of cable at hub so pushed it hard into hub
as you can see from the different colours top and bottom this cable has an outer joined in the middle dunno why
dunno how much grease I got in but the spiral will pull it down over time I think.
test driver later
20180826_112640 by Paul_Barr, on Flickr
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: Speedo Bounce
itchyfeet wrote:
tested it with drill first and seems better worse when inner is out of cable at hub so pushed it hard into hub
That bit didn't make sense to me
If you do get a new Gemo and grease it, how are you going to determine success ? Won't it be a few years before the normal failure fails to occur ?
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
Re: Speedo Bounce
Agreed.My needle didn't bounce for at least a year after the cable was fitted.
2.1 LPG/Petrol Auto Caravelle
"The difference between genius and stupidity is that genius has its limits"
"The difference between genius and stupidity is that genius has its limits"
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Speedo Bounce
937carrera wrote:itchyfeet wrote:
tested it with drill first and seems better worse when inner is out of cable at hub so pushed it hard into hub
That bit didn't make sense to me
?
with the drill if you pull inner away from outer at hub you get more vibration.
its easy to get a new gemo to bounce in my experience by position but if greased its very stable then it suggests to me thats the issue but you are right its a long term test.
I'm hoping this will work with vw cable and somebody else is going to do the greasing of a gemo test.