fuse keeps blowing
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 56
- Joined: 18 Oct 2017, 12:52
- 80-90 Mem No: 16295
- Location: Portlethen
fuse keeps blowing
Help please, I keep blowing and half melting a 8 amp fuse, which runs the heater / blower, this is a real hotch podge tangle of wiring and its very difficult to find wires and find out what they all do.
I wish I could rip it all out and start again but I can't.
Should I just put a bigger fuse in and hope for the best?
I wish I could rip it all out and start again but I can't.
Should I just put a bigger fuse in and hope for the best?
1980 Super viking with a 1.9 Polo Diesel conversion
-
- Registered user
- Posts: 1937
- Joined: 29 Sep 2012, 12:00
- 80-90 Mem No: 11783
- Location: s. cheshire
Re: fuse keeps blowing
I think it should be a 20amp fuse for the blower. Haven't got a diagram in front of me only toilet paper so can't be certain.
1.9td AAZ
T25 - an adventure before dementia
T25 - an adventure before dementia
- nicq
- Registered user
- Posts: 1185
- Joined: 24 Sep 2011, 19:03
- 80-90 Mem No: 10290
- Location: Cranleigh Surrey
Re: fuse keeps blowing
lefty67 wrote:I think it should be a 20amp fuse for the blower. Haven't got a diagram in front of me only toilet paper so can't be certain.
2.1 Twin slider
-
- Registered user
- Posts: 4447
- Joined: 13 Jan 2010, 12:42
- 80-90 Mem No: 4418
- Location: West London - 1985 westie pop top, LHD, 1900 DF engine
Re: fuse keeps blowing
And also replace those plastic bullet fuses with ceramic ones, so they cannot melt.
Re: fuse keeps blowing
When this happened to me it was the blower motor.I hope that's not the case with you as it's a dash out job.
2.1 LPG/Petrol Auto Caravelle
"The difference between genius and stupidity is that genius has its limits"
"The difference between genius and stupidity is that genius has its limits"
- jrt
- Registered user
- Posts: 3418
- Joined: 01 Oct 2011, 15:53
- 80-90 Mem No: 10288
- Location: East Cheshire
Re: fuse keeps blowing
fuse no 10 16 amp for the blower and wipers on my van- 1983 DG according to the handbook.
David
David
the future is unwritten
- bigbadbob76
- Registered user
- Posts: 1733
- Joined: 07 Nov 2016, 14:41
- 80-90 Mem No: 15707
- Location: Isle of Skye
Re: fuse keeps blowing
Mine too, blower motor was seized and drawing big amps.
Replaced the motor but the damage was already done to the fuse box so it melts plastic fuses.
I avoid using the motor on full blast.
Replaced the motor but the damage was already done to the fuse box so it melts plastic fuses.
I avoid using the motor on full blast.
'86 1.9 DG, 4 spd, tintop, camper conversion.
Split case club member.
Split case club member.
- CovKid
- Trader
- Posts: 8409
- Joined: 30 Apr 2006, 13:19
- 80-90 Mem No: 3529
- Location: Ralph - Coventry (Retired)
- Contact:
Re: fuse keeps blowing
If a 16amp fuse blows when blower is running, the only way forward is to replace blower. If its an original blower motor it will now be drawing considerably more amps on startup than when it was new. Unfortunately most original blowers have already reached the end of their lives, or are about to. Sticking in bigger fuses might make the motor go, but the risk of a dash fire is much greater. If you dig around you'll find (in WIKI) a how to on removing dash as well as my PWM blower control upgrade.
You should also remove wiper supply from present fuse, and provide an independent fuse. (also in WIKI)
You should also remove wiper supply from present fuse, and provide an independent fuse. (also in WIKI)
Last edited by CovKid on 08 Nov 2017, 12:07, edited 1 time in total.
Roller paint your camper at home: http://roller.epizy.com/55554/" onclick="window.open(this.href);return false; for MP4 download.
Re: fuse keeps blowing
Ralf85 wrote:And also replace those plastic bullet fuses with ceramic ones, so they cannot melt.
Ceramic fuses are surprisingly hard to find these days. But the plastic fuses ought to be able to handle their rated current without melting, and should blow by breaking the metal link when the current rating is exceeded, rather than by melting.
So it's possible that the heat that's causing the fuse to melt is actually coming from a less-than-perfect connection between the wire and the fuse. If some of the strands in the wire have broken at the crimp, or the spade connector is a bit loose or corroded, then the connector may not be able to carry the required current comfortably and will heat up. I had exactly this problem, and the heat had caused the cable sheath to go brittle over several inches from the fusebox. I replaced the entire cable in the end.
Another thing to point out is that in pre-85 vans this fuse also supplies the wiper motor - lose one and you lose both. A crazy idea given that if it's wet outside there's a good chance your clothes will be damp and you're more likely to need the blower motor. Somebody obviously decided at some point that it was a good idea to put two high current devices, that are often likely to be needed at the same time, on the same fuse. There's an article in the wiki on how to separate these two items onto different fuses.
"I'm a man of means, by no means....King of the Road!"
1983 Viking Xplorer, 2.1DJ
1983 Viking Xplorer, 2.1DJ
-
- Registered user
- Posts: 633
- Joined: 12 Aug 2010, 06:57
- 80-90 Mem No: 8608
- Location: Fairly close to Hinckley
Re: fuse keeps blowing
I purchased a circuit breaker bladed fuse for the blower motor, just to be on the safe side.
Sent from my F3111 using Tapatalk
Sent from my F3111 using Tapatalk
“A sure cure for seasickness is to sit under a tree.” ― Spike Milligan
1988 1.9 DG
1988 1.9 DG
-
- Registered user
- Posts: 4447
- Joined: 13 Jan 2010, 12:42
- 80-90 Mem No: 4418
- Location: West London - 1985 westie pop top, LHD, 1900 DF engine
Re: fuse keeps blowing
I bought ceramic bullet fuses online. Also, try and get copper ones instead of the original aluminium ones, which cause corrosion and resistance build up with the copper connectors.
- Oldiebut goodie
- Registered user
- Posts: 7294
- Joined: 18 Apr 2008, 01:19
- 80-90 Mem No: 11135
- Location: Eastern Angle
Re: fuse keeps blowing
My Merc has got copper ones (tinned) but they still get crusty at the contact point. No moisture where they are situated to cause corrosion other than the sea air which I can't get away from.
1.6D 2019 VW T-Cross
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶
200hp VW T6
1̶Y̶ ̶1̶9̶8̶7̶ ̶H̶i̶-̶t̶o̶p̶ ̶C̶a̶r̶a̶v̶e̶l̶l̶e̶
5̶0̶8̶d̶ ̶M̶e̶r̶c̶