Sorry if it’s been done to death... but have searched wiki and archive I can’t find the answer. I need to fit two lap belts to the back of my T25 holdsworth conversion. I have bought the belts from Jk with suitable mounting plates. I’m fine to weld... just not sure on the the mounting point locations.
I have installed previous in stocks cars and the rules used to be no less than 15”apart... and a 70 angle going forward to the seat. I will prob replace with 3point at later date but need the, sorted to use van
Is there any direction on how best to install please it looks like mounting plate in middle and then other plate to the wheel arch.. any help or direction appreciated
Fitting lap belts ( I’ve checked and can’t find answer :-) )
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 293
- Joined: 04 Sep 2012, 21:25
- 80-90 Mem No: 11532
- Location: Wiltshire
Re: Fitting lap belts ( I’ve checked and can’t find answer :-) )
biker1981 wrote:Sorry if it’s been done to death... but have searched wiki and archive I can’t find the answer. I need to fit two lap belts to the back of my T25 holdsworth conversion. I have bought the belts from Jk with suitable mounting plates. I’m fine to weld... just not sure on the the mounting point locations.
I have installed previous in stocks cars and the rules used to be no less than 15”apart... and a 70 angle going forward to the seat. I will prob replace with 3point at later date but need the, sorted to use van
Is there any direction on how best to install please it looks like mounting plate in middle and then other plate to the wheel arch.. any help or direction appreciated
Was your van a caravelle or panel van? If it was a caravelle the mounts should already be there with a round plastic cap with a Phillips head keeping them sealed.
The exact rule will be in here:
http://www.legislation.gov.uk/uksi/1986 ... tents/made
Refers to this document which has all your specs you were after at para 4.1 specifications
https://eur-lex.europa.eu/legal-content ... 31976L0115
Greta: 85’ LHD 2.5L Subaru 14in Syncro
http://forum.club8090.co.uk/viewtopic.php?t=165773
http://forum.club8090.co.uk/viewtopic.php?t=165773
Re: Fitting lap belts ( I’ve checked and can’t find answer :-) )
adie89 wrote:biker1981 wrote:Sorry if it’s been done to death... but have searched wiki and archive I can’t find the answer. I need to fit two lap belts to the back of my T25 holdsworth conversion. I have bought the belts from Jk with suitable mounting plates. I’m fine to weld... just not sure on the the mounting point locations.
I have installed previous in stocks cars and the rules used to be no less than 15”apart... and a 70 angle going forward to the seat. I will prob replace with 3point at later date but need the, sorted to use van
Is there any direction on how best to install please it looks like mounting plate in middle and then other plate to the wheel arch.. any help or direction appreciated
Was your van a caravelle or panel van? If it was a caravelle the mounts should already be there with a round plastic cap with a Phillips head keeping them sealed.
The exact rule will be in here:
http://www.legislation.gov.uk/uksi/1986 ... tents/made
Refers to this document which has all your specs you were after at para 4.1 specifications
https://eur-lex.europa.eu/legal-content ... 31976L0115
No was just a converted panel van I’m afraid
Re: Fitting lap belts ( I’ve checked and can’t find answer :-) )
biker1981 wrote:adie89 wrote:biker1981 wrote:Sorry if it’s been done to death... but have searched wiki and archive I can’t find the answer. I need to fit two lap belts to the back of my T25 holdsworth conversion. I have bought the belts from Jk with suitable mounting plates. I’m fine to weld... just not sure on the the mounting point locations.
I have installed previous in stocks cars and the rules used to be no less than 15”apart... and a 70 angle going forward to the seat. I will prob replace with 3point at later date but need the, sorted to use van
Is there any direction on how best to install please it looks like mounting plate in middle and then other plate to the wheel arch.. any help or direction appreciated
Was your van a caravelle or panel van? If it was a caravelle the mounts should already be there with a round plastic cap with a Phillips head keeping them sealed.
The exact rule will be in here:
http://www.legislation.gov.uk/uksi/1986 ... tents/made
Refers to this document which has all your specs you were after at para 4.1 specifications
https://eur-lex.europa.eu/legal-content ... 31976L0115
No was just a converted panel van I’m afraid
Many thanks