Autosleeper Hi Top strip out
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 162
- Joined: 14 Feb 2012, 19:17
- 80-90 Mem No: 10711
- Location: Ryde, Isle of Wight
Autosleeper Hi Top strip out
I'll be putting my Autosleeper Hi top in to the garage after Christmas to have the top taken off and all the rot underneath dealt with plus new gutters and other bits attended to.
I want to strip out the inside of all the storage, bunk bed and anything else required so that the garage will have access to remove the Hi Top.
Had a search on these forums and Youtube but couldn't find anything.
Any guidance on where to start and any tips would be greatly appreciated.
I want to strip out the inside of all the storage, bunk bed and anything else required so that the garage will have access to remove the Hi Top.
Had a search on these forums and Youtube but couldn't find anything.
Any guidance on where to start and any tips would be greatly appreciated.
1987 DG 1900 petrol plus Yamaha Midnight Star and Yamaha Virago and !979 Vespa P125X
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: Autosleeper Hi Top strip out
There's a little bit of help in this thread on one of the trickier areas
http://forum.club8090.co.uk/viewtopic.php?f=39&t=161757
I have stripped out a LeisureDrive interior. Just start unscrewing what you can to reveal more bits to remove, if I remember correctly I did it in a few hours
http://forum.club8090.co.uk/viewtopic.php?f=39&t=161757
I have stripped out a LeisureDrive interior. Just start unscrewing what you can to reveal more bits to remove, if I remember correctly I did it in a few hours
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
-
- Registered user
- Posts: 162
- Joined: 14 Feb 2012, 19:17
- 80-90 Mem No: 10711
- Location: Ryde, Isle of Wight
Re: Autosleeper Hi Top strip out
Many thanks, one of the links ends up showing how to remove the rear cupboard which is really helpful.
Might invest in some good hard drills for dealing with rotten screw heads !
Might invest in some good hard drills for dealing with rotten screw heads !
1987 DG 1900 petrol plus Yamaha Midnight Star and Yamaha Virago and !979 Vespa P125X
-
- Registered user
- Posts: 2481
- Joined: 07 Jan 2009, 20:36
- 80-90 Mem No: 6085
- Location: Old Somerby,Grantham
Re: Autosleeper Hi Top strip out
let us know how you get on with this as I would be too scared to see what mines like with the top off, if I had the money to get it done
Nil carborundum illegitimi
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: Autosleeper Hi Top strip out
Glad it helped - what have you done with the 12v spotlight, I can see the lwer is connected to a white box ?
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
-
- Registered user
- Posts: 162
- Joined: 14 Feb 2012, 19:17
- 80-90 Mem No: 10711
- Location: Ryde, Isle of Wight
Re: Autosleeper Hi Top strip out
937carrera wrote:Glad it helped - what have you done with the 12v spotlight, I can see the lwer is connected to a white box ?
I think its still knocking around in my bits and pieces box. Didn't seem to give out much light. "White box" is a chinese LED headlight, taken apart, folded out and mounted with a diffuser plate over the front. Gives loads of light with low consumption.
1987 DG 1900 petrol plus Yamaha Midnight Star and Yamaha Virago and !979 Vespa P125X
-
- Registered user
- Posts: 647
- Joined: 27 May 2007, 20:48
- 80-90 Mem No: 875
- Location: Weald, Kent
Re: Autosleeper Hi Top strip out
Hi,
You should not have too much trouble.
Up front.... remove the cupboard doors then un screw the crockery cupboard but leave in place.. The crock cupboard has some small angle brackets fixing it in place. Next remove vertical sheet. The ply sheet over the cab is screwed down if I remember rightly. Trouble is the screws, I think, were put in before the carpet. You just have to feel around for the heads.
At the rear. The small locker should come out with the upper floor. You might not need to remove the side boxes but I cannot help there as I have never removed them. The ply sheets over the cab etc are not necessarily in one piece.
Hope this little bit of info helps.
It might save a couple of pennies if you can dig/scrape/remove sealant along the sides before the garage has it. That is a time consuming job.
You should not have too much trouble.
Up front.... remove the cupboard doors then un screw the crockery cupboard but leave in place.. The crock cupboard has some small angle brackets fixing it in place. Next remove vertical sheet. The ply sheet over the cab is screwed down if I remember rightly. Trouble is the screws, I think, were put in before the carpet. You just have to feel around for the heads.
At the rear. The small locker should come out with the upper floor. You might not need to remove the side boxes but I cannot help there as I have never removed them. The ply sheets over the cab etc are not necessarily in one piece.
Hope this little bit of info helps.
It might save a couple of pennies if you can dig/scrape/remove sealant along the sides before the garage has it. That is a time consuming job.
1987/8 Autosleeper, 1.9dg (Automatic) hightop. Petrol/ LPG
-
- Registered user
- Posts: 162
- Joined: 14 Feb 2012, 19:17
- 80-90 Mem No: 10711
- Location: Ryde, Isle of Wight
Re: Autosleeper Hi Top strip out
Many thanks for the advice and tips, much appreciated and will make the task a bit easier
1987 DG 1900 petrol plus Yamaha Midnight Star and Yamaha Virago and !979 Vespa P125X
Re: Autosleeper Hi Top strip out
I don't seem to have any signs of rust or decay problems in my Leisure drive high top and without doing some intrusive digging about I am not sure how to find any problems. I can't see any bolts or fixing method and wonder if the high top is simply "stuck" on. If so then maybe I need to determine the life of the adhesive system.
Anyone know how the high top is retained as I should hate for it to go flying so to speak?
CS
E D I T: I just found them on t'internet and wonder if they want back the rusty old upholstery sheers I found when rebuilding the side door.
Anyone know how the high top is retained as I should hate for it to go flying so to speak?
CS
E D I T: I just found them on t'internet and wonder if they want back the rusty old upholstery sheers I found when rebuilding the side door.
Well-timed silence hath more eloquence than speech.
"A quiet shy boy who took little part in games or sport"
88 High top 2.1 WBX
"A quiet shy boy who took little part in games or sport"
88 High top 2.1 WBX
-
- Registered user
- Posts: 162
- Joined: 14 Feb 2012, 19:17
- 80-90 Mem No: 10711
- Location: Ryde, Isle of Wight
Re: Autosleeper Hi Top strip out
Making progress !! Got all the rear bed and shelf unit off. The rear cupboard came out quite easy after dealing with rotten screws. Many thanks for the tips.
Now left with the box sections left and right where strip lights and leisure electrics are. Is it a case of peeling off the carpet lining and looking for fixing screws ?
Any suggestions much appreciated.
Now left with the box sections left and right where strip lights and leisure electrics are. Is it a case of peeling off the carpet lining and looking for fixing screws ?
Any suggestions much appreciated.
1987 DG 1900 petrol plus Yamaha Midnight Star and Yamaha Virago and !979 Vespa P125X