Fisher Price - My first welding and fabrication
Moderators: User administrators, Moderators
-
- Registered user
- Posts: 1809
- Joined: 10 May 2013, 11:59
- 80-90 Mem No: 13706
- Location: Central Scotland
Re: Fisher Price - My first welding and fabrication
Have you ever seen an unhappy fool?
88 Transporter with hitop camper conversion, 1.6td.
88 Transporter with hitop camper conversion, 1.6td.
- orangebooboobearcrew
- Registered user
- Posts: 142
- Joined: 20 Jan 2008, 14:58
- 80-90 Mem No: 3718
- Location: Tamworth, Staffs
Re: Fisher Price - My first welding and fabrication
All,
Thanks for your posts and words of encouragement.
At the end of the day, I am just an ordinary guy 'having a go'. Did lots of reading, youtube videos, chatted to a few old skool pals who have welded and got on the Migwelding forum.
I'll admit, after buying my MIG (Clarke 151 turbo) it sat in the garage for best part of 2 years and I was scared of it - after all, I could set myself / van / house on fire, blow up the fuel tank, blow up the gas canister, electrocute myself, blind myself, kill myself with toxic fumes - the list goes on.
But I finally plucked up the courage to have a go and it was the best thing I have done. In fact, once you have a practice and get the basics, it's actually pretty easy; like everything, preparation is the key.
My welding isn't pretty, but it works and as someone said, careful use of the grinder can hide a multitude of sins.
The metal I am using is 1mm mild sheet steel which I bought from Just Crappers for about £20. This should be enough for what I am working on.
Using 0.6mm wire on Clarke 151 welder.
Gas is Hobbyweld 5 argon/Co2 mix. It was £37 for the refill, about £70 for the deposit but you get that back at the end.
I'm back to the unit tomorrow, so progress update / pics will follow..
Thanks for your posts and words of encouragement.
At the end of the day, I am just an ordinary guy 'having a go'. Did lots of reading, youtube videos, chatted to a few old skool pals who have welded and got on the Migwelding forum.
I'll admit, after buying my MIG (Clarke 151 turbo) it sat in the garage for best part of 2 years and I was scared of it - after all, I could set myself / van / house on fire, blow up the fuel tank, blow up the gas canister, electrocute myself, blind myself, kill myself with toxic fumes - the list goes on.
But I finally plucked up the courage to have a go and it was the best thing I have done. In fact, once you have a practice and get the basics, it's actually pretty easy; like everything, preparation is the key.
My welding isn't pretty, but it works and as someone said, careful use of the grinder can hide a multitude of sins.
The metal I am using is 1mm mild sheet steel which I bought from Just Crappers for about £20. This should be enough for what I am working on.
Using 0.6mm wire on Clarke 151 welder.
Gas is Hobbyweld 5 argon/Co2 mix. It was £37 for the refill, about £70 for the deposit but you get that back at the end.
I'm back to the unit tomorrow, so progress update / pics will follow..
-
- Trader
- Posts: 8047
- Joined: 12 Oct 2005, 20:55
- 80-90 Mem No: 1948
- Location: lincolnshire
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Fisher Price - My first welding and fabrication
Anybody know what gas flow is reasonable
I have a flow gauge in litres/minuite?
I have a flow gauge in litres/minuite?
- orangebooboobearcrew
- Registered user
- Posts: 142
- Joined: 20 Jan 2008, 14:58
- 80-90 Mem No: 3718
- Location: Tamworth, Staffs
Re: Fisher Price - My first welding and fabrication
I was told to hold the torch against your cheek and when you can just feel the gas that is enough - any more is wasting gas, Don't know if that's good advice or not but it seems to be welding ok.
MM - you are the bodywork sage and I bow down before ye and doth my cap.
Is that panel double skinned and if so how much is one?
If not, do you do the inner one as well and if so,how much for each?
MM - you are the bodywork sage and I bow down before ye and doth my cap.
Is that panel double skinned and if so how much is one?
If not, do you do the inner one as well and if so,how much for each?
Re: Fisher Price - My first welding and fabrication
itchyfeet wrote:Anybody know what gas flow is reasonable
I have a flow gauge in litres/minuite?
down as much as need be. if you get the "popcorn" look (porosity) turn it up til it goes
everytime you masterbate god kills a kitten! member 1289 does this still mean owt?
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Fisher Price - My first welding and fabrication
Thanks Rowlesy
-
- Registered user
- Posts: 804
- Joined: 09 Aug 2009, 21:53
- 80-90 Mem No: 8265
- Location: County Monaghan, Ireland
Re: Fisher Price - My first welding and fabrication
I set mine at around 10 litres per minute.
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
1984 1.9D (AEF Code) T25 tintop
-
- Trader
- Posts: 8047
- Joined: 12 Oct 2005, 20:55
- 80-90 Mem No: 1948
- Location: lincolnshire
Re: Fisher Price - My first welding and fabrication
fit one of these
https://www.toolstoday.co.uk/parweld-ga ... 7Qod5UMG2w" onclick="window.open(this.href);return false;
vary the flow dependent on weld and wind(if outdoors)
mm
https://www.toolstoday.co.uk/parweld-ga ... 7Qod5UMG2w" onclick="window.open(this.href);return false;
vary the flow dependent on weld and wind(if outdoors)
mm
-
- Registered user
- Posts: 2824
- Joined: 05 Oct 2012, 08:55
- 80-90 Mem No: 11974
- Location: Salisbury
Re: Fisher Price - My first welding and fabrication
Oh my giddy aunt, never seen one of those. Looks as though it does what it says on the tin.
Why would the glass be anything other than half full?
'89 panel van, 1.9 DG.
'89 panel van, 1.9 DG.
- bigbadbob76
- Registered user
- Posts: 1733
- Joined: 07 Nov 2016, 14:41
- 80-90 Mem No: 15707
- Location: Isle of Skye
Re: Fisher Price - My first welding and fabrication
Congratulations Orange, you've got over the worst bit... making that first cut, you'll soon get the hang of grinding out and welding in, it does take a bit of encouragement from those who know what they're doing ( I was wary at first too) but don't be scared to grind it out if it's rusty, leaving rust in there will just rot your hard work. and don't be tempted to hide rusty bits behind patches.
Your welding will get better and better as you work your way around the van. practice makes perfect. don't forget to paint or spray the back side of your patches where possible, this can be tricky in the blind spots.
Good luck and enjoy it.
Your welding will get better and better as you work your way around the van. practice makes perfect. don't forget to paint or spray the back side of your patches where possible, this can be tricky in the blind spots.
Good luck and enjoy it.
'86 1.9 DG, 4 spd, tintop, camper conversion.
Split case club member.
Split case club member.
-
- Registered user
- Posts: 804
- Joined: 09 Aug 2009, 21:53
- 80-90 Mem No: 8265
- Location: County Monaghan, Ireland
Re: Fisher Price - My first welding and fabrication
Keep up the good work, its all about getting stuck in and learning as you go.
I grew up on a farm so was used to welding stuff with a stick welder, but hadn't touched a mig at all until I started doing my van.
A few things that I learned along the way -
An autodarkening helmet is a must-have.
Keep a stock of spare tips.
Clean your welding mask so you can actually see through it.
Have good lighting around where you are welding so you can see what you're doing.
Make your metal as clean as possible before you weld - I mostly grit blasted.
The black transit paint on new panels is useless. Remove it and put proper primer and paint on it.
Use weld through aerosol primer between seams/overlapped areas.
Use an 8mm drill to make holes for plug welds.
You can cool your welds as you go along with an airgun and a compressor - helps to reduce warpage.
Adjust the tension on your wire reel so that it moves freely and your wire speed isn't getting slowed down or made erratic.
Use cereal packet cardboard to make templates for new metal to be welded in.
I reused most of the good bits of the tall arches that I cut off, as patches for other areas.
I grew up on a farm so was used to welding stuff with a stick welder, but hadn't touched a mig at all until I started doing my van.
A few things that I learned along the way -
An autodarkening helmet is a must-have.
Keep a stock of spare tips.
Clean your welding mask so you can actually see through it.
Have good lighting around where you are welding so you can see what you're doing.
Make your metal as clean as possible before you weld - I mostly grit blasted.
The black transit paint on new panels is useless. Remove it and put proper primer and paint on it.
Use weld through aerosol primer between seams/overlapped areas.
Use an 8mm drill to make holes for plug welds.
You can cool your welds as you go along with an airgun and a compressor - helps to reduce warpage.
Adjust the tension on your wire reel so that it moves freely and your wire speed isn't getting slowed down or made erratic.
Use cereal packet cardboard to make templates for new metal to be welded in.
I reused most of the good bits of the tall arches that I cut off, as patches for other areas.
1984 1.9D (AEF Code) T25 tintop
- bigbadbob76
- Registered user
- Posts: 1733
- Joined: 07 Nov 2016, 14:41
- 80-90 Mem No: 15707
- Location: Isle of Skye
Re: Fisher Price - My first welding and fabrication
I'll add one in there..
Keep the gas flowing between welds when you're stitching panels on with the on-off method. just let the trigger half off so the current stops but the gas still flows. it keeps the oxygen away from the weld until it's cooled.
Keep the gas flowing between welds when you're stitching panels on with the on-off method. just let the trigger half off so the current stops but the gas still flows. it keeps the oxygen away from the weld until it's cooled.
'86 1.9 DG, 4 spd, tintop, camper conversion.
Split case club member.
Split case club member.
- orangebooboobearcrew
- Registered user
- Posts: 142
- Joined: 20 Jan 2008, 14:58
- 80-90 Mem No: 3718
- Location: Tamworth, Staffs
Re: Fisher Price - My first welding and fabrication
Lots of great advice there guys - thanks
Haven't had chance to post up pics from last weekend yet but will try and do it soon...
Haven't had chance to post up pics from last weekend yet but will try and do it soon...