1.9 DG rear oil sender leak
Moderators: User administrators, Moderators
- Savara
- Registered user
- Posts: 72
- Joined: 06 Jun 2018, 14:17
- 80-90 Mem No: 0
- Location: Brighton, East Sussex
- Contact:
1.9 DG rear oil sender leak
Hi all - it looks like the oil sender thing on the rear of the engine has sprung a leak. The haynes doesn't say a lot about this one! What's the story? Does it have a gasket? O ring? Easy to get a socket on it without removing too much or is it water pump off? Any help much appreciated..
- Attachments
-
- OIL.jpg (53.71 KiB) Viewed 3465 times
1991 Holdsworth Villa 3 1.9DG
"Everything in moderation, including moderation" Oscar Wilde
"Everything in moderation, including moderation" Oscar Wilde
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: 1.9 DG rear oil sender leak
No oring two copper washers one for the sensor one for the adapter.
difficult to get to yes
difficult to get to yes
- ajsimmo
- Trader
- Posts: 2701
- Joined: 23 Mar 2009, 14:06
- 80-90 Mem No: 6542
- Location: Isle of Arran
- Contact:
Re: 1.9 DG rear oil sender leak
Must.....resist..... temptation....aaaah, it's no good - the urge is too strong!!!
It's a switch, not a sender. It's on the front of the engine, not the back.
There. Phew, that's better. Soz but it's a compulsion I suffer from.
Sent from my ONEPLUS A3003 using Tapatalk
It's a switch, not a sender. It's on the front of the engine, not the back.
There. Phew, that's better. Soz but it's a compulsion I suffer from.
Sent from my ONEPLUS A3003 using Tapatalk
The Campershack - (website paused)
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
- Mocki
- Membership Admin
- Posts: 16977
- Joined: 29 Sep 2005, 09:27
- 80-90 Mem No: 428
- Location: Mansfield Notts
- Contact:
Re: 1.9 DG rear oil sender leak
ajsimmo wrote:Must.....resist..... temptation....aaaah, it's no good - the urge is too strong!!!
It's a switch, not a sender. It's on the front of the engine, not the back.
There. Phew, that's better. Soz but it's a compulsion I suffer from.
Sent from my ONEPLUS A3003 using Tapatalk
Steve
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
tel / txt O7947-137911
________________
1989 2.1LpgWBX HiTop Leisuredrive Camper
1988 2.1 Caravelle TS TinTop Camper
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: 1.9 DG rear oil sender leak
Oh I missed that
I really must try and be more pedantic
I really must try and be more pedantic
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: 1.9 DG rear oil sender leak
If will be easier for you to get to the switch if you remove the drive belt
[Pedant mode] note I didn't call it a fan belt or an alternator belt
I am going to express a different view as to the location of the switch. For me it is on the rear of the engine, for the same reason that number 1 cylinder can also be called the right hand bank. Even if I'm underneath looking up [/Pedant mode]
[Pedant mode] note I didn't call it a fan belt or an alternator belt
I am going to express a different view as to the location of the switch. For me it is on the rear of the engine, for the same reason that number 1 cylinder can also be called the right hand bank. Even if I'm underneath looking up [/Pedant mode]
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- Savara
- Registered user
- Posts: 72
- Joined: 06 Jun 2018, 14:17
- 80-90 Mem No: 0
- Location: Brighton, East Sussex
- Contact:
Re: 1.9 DG rear oil sender leak
An oil sender is a sender. An "oil sender thing" IS a switch! Heheh..
So if I remove the fanbelt from the rear of the engine I can get a round tube spanner in there with a clicky arm spanner and replace the copper doughnut on the sender?
Not at the van right now, heading there in morning...
So if I remove the fanbelt from the rear of the engine I can get a round tube spanner in there with a clicky arm spanner and replace the copper doughnut on the sender?
Not at the van right now, heading there in morning...
1991 Holdsworth Villa 3 1.9DG
"Everything in moderation, including moderation" Oscar Wilde
"Everything in moderation, including moderation" Oscar Wilde
- bigherb
- Registered user
- Posts: 2579
- Joined: 27 Mar 2008, 13:50
- 80-90 Mem No: 5789
- Location: West Kent
Re: 1.9 DG rear oil sender leak
Not in the world of VW flat fours, the front of the engine is the flywheel end.ajsimmo wrote:It's on the front of the engine, not the back.
There. Phew, that's better. Soz but it's a compulsion I suffer from.
1982 Camper 1970 1500 Beetle Various Skoda's, Ariel Arrow
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: 1.9 DG rear oil sender leak
Savara wrote:An oil sender is a sender. An "oil sender thing" IS a switch! Heheh..
So if I remove the fanbelt from the rear of the engine I can get a round tube spanner in there with a clicky arm spanner and replace the copper doughnut on the sender?
Not at the van right now, heading there in morning...
After all that you went and called it a fanbelt
I did it with a socket and ratchet. 24mm off the top of my head
Removing isn't too bad (from underneath), getting the new one started on the threads depends on how big your hands are (from the top)
Let us know how you get on
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- ajsimmo
- Trader
- Posts: 2701
- Joined: 23 Mar 2009, 14:06
- 80-90 Mem No: 6542
- Location: Isle of Arran
- Contact:
Re: 1.9 DG rear oil sender leak
bigherb wrote: Not in the world of VW flat fours, the front of the engine is the flywheel end.
That must be an air-cooled thing. So when asked to replace the rear main oil seal, you'd remove the front (sorry, rear) pulley? That's a bit rum. Don't often hear people say "just got to bolt the gearbox onto the front of my engine"
Number one's still on the right whichever way you look at it (unless you're inside hanging over the back seat), but back right. )
Sent from my ONEPLUS A3003 using Tapatalk
The Campershack - (website paused)
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: 1.9 DG rear oil sender leak
Are we ready for confusion
RMS is always at the flywheel end, but in a transverse engine it will be located on either the left or right hand side of the car, so I can see why you say the RMS is at the rear of the engine.
Move to a different car, say recent Boxster / 911. They have essentially the same engine, different capacities. In the Boxster the gearbox is behind the engine, in the 911 the gearbox is ahead of the engine, in the traditional layout. Number 1 cylinder can therefore be on the right or the left.
I borrowed the following from another site. VW original numbering convention seems to be at odds with the later DIN , though the industrial engines would comply
Convention sometimes plays a part too. Do you refer to the straight edge that you measure with as a ruler or a rule (ultra pedant mode on)
RMS is always at the flywheel end, but in a transverse engine it will be located on either the left or right hand side of the car, so I can see why you say the RMS is at the rear of the engine.
Move to a different car, say recent Boxster / 911. They have essentially the same engine, different capacities. In the Boxster the gearbox is behind the engine, in the 911 the gearbox is ahead of the engine, in the traditional layout. Number 1 cylinder can therefore be on the right or the left.
I borrowed the following from another site. VW original numbering convention seems to be at odds with the later DIN , though the industrial engines would comply
From page 395 of the Bosch Automotive Handbook, 5th edition:
Number the cylinders
(DIN 73021)
[ Applies to motor vehicles only. For internal combustion engines for general and marine use, the reverse direction (as viewed looking at the power-output end) is standardized (ISO 1204 and 1205, DIN 6265).]
The cylinders are numbered consecutively 1, 2, 3, etc. in the order in which they would be intersected by an imaginary reference plane. As viewed looking at the end of the engine opposite the power-out-put end. This plane is located to the left when numbering begins; the numerical assignments the proceed clockwise around the longitudinal axis of the engine [ fiqures are referenced ]. If there is more than one cylinder in a reference plane, the cylinder nearest the observer is assigned the number 1, with consecutive numbers being assigned to the following cylinders. Cylinder 1 is to be identified by the number 1.
The figure for a flat engine shows the #1 cylinder is the when looking at the engine from the power output end is located on the right bank at the furtherest cylinder from the power output end.
Convention sometimes plays a part too. Do you refer to the straight edge that you measure with as a ruler or a rule (ultra pedant mode on)
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- ajsimmo
- Trader
- Posts: 2701
- Joined: 23 Mar 2009, 14:06
- 80-90 Mem No: 6542
- Location: Isle of Arran
- Contact:
Re: 1.9 DG rear oil sender leak
Well, that's that cleared up then.
Sent from my ONEPLUS A3003 using Tapatalk
Sent from my ONEPLUS A3003 using Tapatalk
The Campershack - (website paused)
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: 1.9 DG rear oil sender leak
ajsimmo wrote:Well, that's that cleared up then.
Wonder if the OP has got the old switch off yet
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: 1.9 DG rear oil sender leak
937carrera wrote:ajsimmo wrote:Well, that's that cleared up then.
Wonder if the OP has got the old switch off yet
it might be a new switch.
- bigherb
- Registered user
- Posts: 2579
- Joined: 27 Mar 2008, 13:50
- 80-90 Mem No: 5789
- Location: West Kent
Re: 1.9 DG rear oil sender leak
The front of the engine faces the front of the vehicle hence why No 1 cylinder is the flywheel end and the main bearings are numbered 1-4 from the flywheel, also applied to Renault rear engined vehicles and when the engine was moved to the front behind the gearbox Renault 4/5/16 but not the rear engined Skodas that was an engine turned around from the front engined previous models and No 1 was at the rear.ajsimmo wrote:
That must be an air-cooled thing. So when asked to replace the rear main oil seal, you'd remove the front (sorry, rear) pulley? That's a bit rum. Don't often hear people say "just got to bolt the gearbox onto the front of my engine"
1982 Camper 1970 1500 Beetle Various Skoda's, Ariel Arrow