Am I Being Naive?
Moderators: User administrators, Moderators
- Snowmark
- Registered user
- Posts: 222
- Joined: 16 Mar 2016, 21:28
- 80-90 Mem No: 15217
- Location: Christchurch, Dorset
Re: Am I Being Naive?
Just an update - exhaust is off! 6 of the studs came clean out with the rusted on nuts, two left in as the nuts came free, think I'll probably leave these as I don't want to push my luck.
VW Speedshop Stainless exhaust to order - any fitting tips/gaskets/nuts etc???
Thanks
VW Speedshop Stainless exhaust to order - any fitting tips/gaskets/nuts etc???
Thanks
1986 1.9DG WBX Autosleeper Hi Top
- DoubleOSeven
- Registered user
- Posts: 2483
- Joined: 25 Jul 2014, 21:10
- 80-90 Mem No: 14520
- Location: Reading, England
- Contact:
Re: Am I Being Naive?
Tip No.1, put the nuts onto the exhaust studs before assembly, just a few turns so they are flush. Then put the studs into the heads. That way the nuts will tighten up long before the studs bottom out, which you ‘don’t’ want. Hope that makes sense.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
1990 Volkswagen Transporter 2.1 Manual
2005 Porsche 911 3.6 Manual
2012 Volkswagen Polo 1.4 Automatic
2005 Porsche 911 3.6 Manual
2012 Volkswagen Polo 1.4 Automatic
- Snowmark
- Registered user
- Posts: 222
- Joined: 16 Mar 2016, 21:28
- 80-90 Mem No: 15217
- Location: Christchurch, Dorset
Re: Am I Being Naive?
I think so - basically, I want the nut to tighten against the exhaust flange before the stud touches and tightens against the casing.......
Makes sense and also, hadn't even considered that - thanks!
Makes sense and also, hadn't even considered that - thanks!
1986 1.9DG WBX Autosleeper Hi Top
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Am I Being Naive?
If you buy stanless grubscrews they have an internal hex to adjust depth and they don't rust.
Balls to anybody who mentions bimetalic corrosion, been using them for 10 years.
Balls to anybody who mentions bimetalic corrosion, been using them for 10 years.
- Snowmark
- Registered user
- Posts: 222
- Joined: 16 Mar 2016, 21:28
- 80-90 Mem No: 15217
- Location: Christchurch, Dorset
Re: Am I Being Naive?
Yep, got SS studs. Spring washer and SS nuts?
1986 1.9DG WBX Autosleeper Hi Top
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Am I Being Naive?
I just use flat washers but no harm in spring ones I can think of.
- ajsimmo
- Trader
- Posts: 2698
- Joined: 23 Mar 2009, 14:06
- 80-90 Mem No: 6542
- Location: Isle of Arran
- Contact:
Re: Am I Being Naive?
Be careful with SS nuts on SS studs, as thread galling could make them impossible to remove undamaged in future. I'd use anti-seize (copper coated) nuts instead, with SS flat washers.
The Campershack - (website paused)
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
WBX Rebuilds & Upgrades from the beautiful Isle of Arran
- Ian Hulley
- Registered user
- Posts: 12659
- Joined: 11 Oct 2005, 08:08
- 80-90 Mem No: 1323
- Location: Wirksworth, Derbyshire ... or at t'mill
Re: Am I Being Naive?
That ^ meant I had to take my engine out it's the stud below the thermostat housing and underneath the bend of the exhaust
Fortunately I've done a fair few over the years
I agree ... freeze-it spray, plus gas, cobalt drills, easy-outs (left handed tapered drills) good quality Vice-grips and precision pointed blow lamp are all essential tools for the aged exhaust removal. I used normal M8 BZP studs and copper-coated M8 exhaust nuts to fit the new system. I removed all the old studs and cleaned out all the threads and copper-slipped them all prior to re-assembly. I also used double nuts where the push rod tube shields are mounted so the exhaust doesn't have to be loosened off should the (stainless) shields ever need to come off.
Ian
The Hulley's Bus
1989 2.1DJ Trampspotter
LPG courtesy of Steve @ Gasure
1989 2.1DJ Trampspotter
LPG courtesy of Steve @ Gasure
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Am I Being Naive?
ajsimmo wrote:Be careful with SS nuts on SS studs, as thread galling could make them impossible to remove undamaged in future. I'd use anti-seize (copper coated) nuts instead, with SS flat washers.
Cheap stainless nuts and studs can have badly formed threads but im my experience its very rare unless you over tighten.
check the nut runs freely on the stud, any grittyness is a badly formed thread.
my whole exhaust is all staless bolts and studs and nuts about 30 in total, been on and off maybe 5 times in 10 years and not galled one
- Snowmark
- Registered user
- Posts: 222
- Joined: 16 Mar 2016, 21:28
- 80-90 Mem No: 15217
- Location: Christchurch, Dorset
Re: Am I Being Naive?
OK, so I'm a complete idiot......
6 out of 8 studs came clean out without a fuss. The other 2 were fine and would have cleaned up to be reused.
For some unknown reason I decided just to try and remove one of the old studs and obviously snapped it......
Today was spent drilling it out. To be honest it went OK (I think). I now have a hole drilled out to 6.5mm and a depth of 19mm. However, the threads have not collapsed as I expected and they seem to be welded to the casing.
I guess my next move is to tap the hole I've made - any help gratefully received.
What tap to buy (currently just have a cheap Aldi set)
Any tips for getting it started? I guess I have to be dead straight.
If I make a proper Horlicks of it is there an escape - could i drill out larger and helicoil or use a M!0 stud that reduces to a M8?
Thanks for any advice - feeling a little stressed.
6 out of 8 studs came clean out without a fuss. The other 2 were fine and would have cleaned up to be reused.
For some unknown reason I decided just to try and remove one of the old studs and obviously snapped it......
Today was spent drilling it out. To be honest it went OK (I think). I now have a hole drilled out to 6.5mm and a depth of 19mm. However, the threads have not collapsed as I expected and they seem to be welded to the casing.
I guess my next move is to tap the hole I've made - any help gratefully received.
What tap to buy (currently just have a cheap Aldi set)
Any tips for getting it started? I guess I have to be dead straight.
If I make a proper Horlicks of it is there an escape - could i drill out larger and helicoil or use a M!0 stud that reduces to a M8?
Thanks for any advice - feeling a little stressed.
1986 1.9DG WBX Autosleeper Hi Top
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: Am I Being Naive?
if you cant remove all the old steel stud you really have to drill out and helicoil M8 helicoil needs a larger hole so should be fine, I have all the helicoils drills and taps if you want to borrow them or they are not so expensive to buy, just like the drill you need to start the tap straight long bolt in the othef hole and align by eye.
P1060051 by Paul_Barr, on Flickr
P1060052 by Paul_Barr, on Flickr
P1060051 by Paul_Barr, on Flickr
P1060052 by Paul_Barr, on Flickr
Re: Am I Being Naive?
Snowmark wrote:Thanks Itchy,
I’ve PM’d you
Good work !!
Sent from my iPhone using Tapatalk
1983 1.9 Ivory Westy Joker