WBXlog

Big lumps of metals and spanners. Including servicing and fluids.

Moderators: User administrators, Moderators

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

500 mile oil and filter today, no bits in the oil, treated it to a rev limiting rotor arm ( please don't tell me they are unreliable), dizzy cap and plugs.

I had forgotten how black oil gets running on petrol, my lpg van isn't this bad after thousands of miles.

Checked compressions and same as before 13 to 14 bar

must get push rod covers on :D
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
ajsimmo
Trader
Posts: 2698
Joined: 23 Mar 2009, 14:06
80-90 Mem No: 6542
Location: Isle of Arran
Contact:

Re: WBXlog

Post by ajsimmo »

itchyfeet wrote:treated it to a rev limiting rotor arm ( please don't tell me they are unreliable)

Ok, you can rely on them to fail.
The Campershack - (website paused)
WBX Rebuilds & Upgrades from the beautiful Isle of Arran

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

Everything fails eventually.
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

Just turned the first 1000 miles today :ok
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

2000 miles not much to say other than the extra power of a DJ over a DG is well worth the effort :D
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
Bigjcc55
Registered user
Posts: 635
Joined: 21 Aug 2011, 08:55
80-90 Mem No: 10140
Location: Ayrshire, scotland

Re: WBXlog

Post by Bigjcc55 »

If don't mind me asking where did you get the tip to add the o ring on the back of the oil pump?


Sent from my iPhone using Tapatalk Pro
1985 1.9 Devon moonraker
1992 2.1 SA big window syncro
1991 TDI syncro panel van

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

Marco Mansi.
he fits three o rings and uses no gaskets but the one shown is the easiest and IMO the other two gaskets works well enough if you reduce the endfloat to zero by wet and dry on the pump body and use the gasket to provide the endfloat.

If ouu never heard of Marco he has been building turbo race WBX for many years and knows his onions
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
Bigjcc55
Registered user
Posts: 635
Joined: 21 Aug 2011, 08:55
80-90 Mem No: 10140
Location: Ayrshire, scotland

Re: WBXlog

Post by Bigjcc55 »

I need to get myself on to face book, seems there is plenty of good info on there.
Where do the other two o rings go?
I like the idea of taking the pump face down and using the gasket.
Less likely to leak.


Sent from my iPhone using Tapatalk Pro
1985 1.9 Devon moonraker
1992 2.1 SA big window syncro
1991 TDI syncro panel van

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

other two orings are in place of the other two gaskets, so other side of oil in and out holes and one on the cover face.
Its not all on facebook,
facebook is rubbish for searching back, its very much todays news, here you have a lot of knoledge you can search on, try searching facebook and you get....computers says no results
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

If anybody is interested Marco Mansi is now selling his three ringed and blueprinted 30mm oil pumps for 120 USD + post, need to be on facebook though.

o ring is recessed more than I did so no mods to oil channels required.

Advert currently on VW T25/T3 VANS AND PARTS FOR SALE group

beware if you buy from USA you will get a VAT bill with a 12 quid handling charge

dunno if this link works

https://www.facebook.com/groups/5605307 ... 2630071971" onclick="window.open(this.href);return false;

Imageoil pump 2 by Paul_Barr, on Flickr

Imageoil pump 1 by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

Engine has been in a year this week and done 3000 miles.
All is well, I never got around to o ringing the oil pump but I will.

Could not resist the sticker :D
Not the original position which was on the front and on the tailgate but I like it there

Image112i by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

Over a year has gone by since I last measured oil pressure and I was a bit disappointed with it so I thought I'd better check it again and I opted for an electric gauge too.

remote T piece in the low pressure switch location

ImageP1090968 by Paul_Barr, on Flickr

made a bracketfor the T piece + sender + oil pressure switch and made the connections in the black box

ImageP1090970 by Paul_Barr, on Flickr

connected my wet gauge to check the electric gauge

ImageP1090984 by Paul_Barr, on Flickr

thermocouple down the oil filler tube, marked it using a spare tube to be sure it was far enough in but not too far to do any harm!

ImageP1090996 by Paul_Barr, on Flickr

ImageP1100002 by Paul_Barr, on Flickr

thats good same as a year ago

idle at 80

ImageP1100004 by Paul_Barr, on Flickr

and then got it up to 100

ImageP1100007 by Paul_Barr, on Flickr

idle at 100

ImageP1100009 by Paul_Barr, on Flickr

still planning the oil pump o ring but just so much else to do
Last edited by itchyfeet on 30 Apr 2018, 18:25, edited 1 time in total.
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

This mornings job is a new set of stainless water pipes, the steel ones are on borrowed time.

oil cooler pipes are fiddly not a great design :roll:

ImageP1100081 by Paul_Barr, on Flickr

The stainless tin top pipe behind pulley needed bending too as it rubbed on the pulley ( as would this one) so it looks like this is common

ImageP1100073 by Paul_Barr, on Flickr

I took it off and used a vice so I didn't stress the weld

ImageP1100074 by Paul_Barr, on Flickr

ImageP1100084 by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

This afternoons job was to replace the injector hoses, these are the last bit of old hose left on the van, everythuing has been replaced with the Brickwerks 100% ethanol grade.

ImageP1100087 by Paul_Barr, on Flickr

ImageP1100088 by Paul_Barr, on Flickr

ImageP1100089 by Paul_Barr, on Flickr

ImageP1100090 by Paul_Barr, on Flickr

ImageP1100093 by Paul_Barr, on Flickr

I also did a spray pattern test as described in the VW manual and a leak test, no leakage and spray looks good although may be hard to see ( click for video)

ImageInjector test by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

User avatar
itchyfeet
Registered user
Posts: 12427
Joined: 23 Jul 2007, 17:24
80-90 Mem No: 12733
Location: South Hampshire

Re: WBXlog

Post by itchyfeet »

That oil pressure gauge has got me depressed so I decided to fit the 30mm pump I have had for a year now.

I was going to O ring it but I just have not got around to it so I took the plunge and fitted it as is.


1st job was to weld up my pump puller that I broke

ImageP1100138 by Paul_Barr, on Flickr

silencer off, tin shroud off, support engine, engine bar off, engine cradel off, crank pulley off, water pipes off....

ImageP1100139 by Paul_Barr, on Flickr


new pump is deeper so need to grind the cover plate down to about 8mm on the vertical sides, then check it fits on a spare case

ImageP1100141 by Paul_Barr, on Flickr

studs are long enough to pull them out 5mm

ImageP1100143 by Paul_Barr, on Flickr

a bit of fettling the pump to get almost zero end float

ImageP1100144 by Paul_Barr, on Flickr

Curil T in place of a gasket and some Dirko HT around the inlet and outlet in horseshoe shapes so the sealant does not end up in the oilway, the Dirko was done yesterday and left 24 hours to set.

ImageP1100146 by Paul_Barr, on Flickr

ImageP1100147 by Paul_Barr, on Flickr

ImageP1100148 by Paul_Barr, on Flickr

ImageP1100151 by Paul_Barr, on Flickr

water pump has play so ideal time to swap it

ImageP1100154 by Paul_Barr, on Flickr

all back took longer than expected because I just had to paint stuff :roll: ( OCD?)

ImageP1100160 by Paul_Barr, on Flickr

please with the results. this was 2.5bar

ImageP1100162 30mm pump by Paul_Barr, on Flickr


this was 1.5 bar

ImageP1100168 30mm pump by Paul_Barr, on Flickr
1988 DG WBX LPG Tin Top
1989 DJ digijet WBX Holdsworth Villa 3 Pop Top
itchylinks

Post Reply