WBX-Unknown
Moderators: User administrators, Moderators
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: WBX-Unknown
I have finally found the specs for the one piece main bearing I knew it would be somewhere on the internet
After searching for bearing specs for KS, Mahle and Glyco I decided to use VW classic to see if the information was there. It was, but the data was a little too rounded for my liking, but I now had part numbers rather than NLA
One piece bearing https://www.volkswagen-classic-parts.de ... 82d97.html "26" mm
Three piece bearing https://www.volkswagen-classic-parts.de ... b7f4e.html "20" mm excluding thrust washers. We already knew this was 19.8mm
I then dropped the part number into a site that had popped up before, though these are oversize, the bearing length remains the same at 25.96mm https://e-shop.eoltas.lt/en/74181630-KOLBENSCHMIDT/
So my one piece bearing has worn 0.07mm while itchys had only worn 0.04mm. I'm happy now that I will be able to get the endfloat back into spec and not have to use three maximum thickness shims
I still want to figure out why there is a dimension difference between the two bearings, but that's just satisfying my intellectual curiosity. My technical German has improved again
After searching for bearing specs for KS, Mahle and Glyco I decided to use VW classic to see if the information was there. It was, but the data was a little too rounded for my liking, but I now had part numbers rather than NLA
One piece bearing https://www.volkswagen-classic-parts.de ... 82d97.html "26" mm
Three piece bearing https://www.volkswagen-classic-parts.de ... b7f4e.html "20" mm excluding thrust washers. We already knew this was 19.8mm
I then dropped the part number into a site that had popped up before, though these are oversize, the bearing length remains the same at 25.96mm https://e-shop.eoltas.lt/en/74181630-KOLBENSCHMIDT/
So my one piece bearing has worn 0.07mm while itchys had only worn 0.04mm. I'm happy now that I will be able to get the endfloat back into spec and not have to use three maximum thickness shims
I still want to figure out why there is a dimension difference between the two bearings, but that's just satisfying my intellectual curiosity. My technical German has improved again
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
Sorry my untrained eye does not see anything wrong where am I looking?
937carrera wrote:Con rod first. Remember axial play at 0.4mm is within spec so that isn't causing the side load
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: WBX-Unknown
Look at the shell between about 11 o clock and 1 o clock. There's a dark curved line with a lighter colour to the shell above, compared to the rest of the shell.
That's where the bearing is more polished & worn, and where the additional side play at the small end is coming from.
That's where the bearing is more polished & worn, and where the additional side play at the small end is coming from.
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
oh hes I see that now thought it was a relflecton.
is that typical of a bent rod then?
is that typical of a bent rod then?
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: WBX-Unknown
Maybe...
Typical would see the same wear on the diagonally opposite shell, which there isn't.
I think I need to take a closer look at the little end of that piston / con rod and see if there is any sign of uneven wear there
Typical would see the same wear on the diagonally opposite shell, which there isn't.
I think I need to take a closer look at the little end of that piston / con rod and see if there is any sign of uneven wear there
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
checked piston/rod/ pin weights?
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: WBX-Unknown
No, not yet, a bent rod weighs the same as a straight one.......Or are you thinking a heavy piston causing torsional stresses on the crank.
It's very difficult to bend a crank and type 4 / WBX ones are pretty strong
It's very difficult to bend a crank and type 4 / WBX ones are pretty strong
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
No I was just stabbing in the dark, perhaps an unbalanced piston/rod/pin can cause wear if you found that one was different you might do some more research on it.
Remind me it's not reground is it, wasn't there talk of grinding marks on that journal, can't remember?
Remind me it's not reground is it, wasn't there talk of grinding marks on that journal, can't remember?
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: WBX-Unknown
The journal specs were a couple of pages ago, the crank is completely standard, almost as new except for main number 4, couple of minor marks on rod number 2 cylinder which I'm OK with now
I put the spec sheet up a couple of pages ago, you must have been enjoying your hols that day
I put the spec sheet up a couple of pages ago, you must have been enjoying your hols that day
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
937carrera wrote:
I put the spec sheet up a couple of pages ago, you must have been enjoying your hols that day
yep on me holls and on a mobile, I may have mentioned that the pics are slow to load so all you see is the text for about 15 minuites if you can even be bothered to wait that long
- 937carrera
- Registered user
- Posts: 3599
- Joined: 05 Apr 2015, 19:29
- 80-90 Mem No: 16333
- Location: N Yorks.
Re: WBX-Unknown
Sorry about that, here's another....
Early case alternator bracket
I've just weighed the rotating assemblies, set out as rod + piston, rod being rod+ shell bearings, piston being piston+gudgeon pin+1 circlip:
1. 569+549 = 1118
2. 568+546 = 1115
3. 567+549 = 1114
4. 567+551 = 1118
They look pretty good, but the kitchen scales I used aren't giving consistent results, so these values were the result of a number of weighings, being sure to repeat the positioning on the scale. They are all as pulled from the case, no cleaning, so this was the actual rotating mass, ignoring oil in the rod.
Early case alternator bracket
I've just weighed the rotating assemblies, set out as rod + piston, rod being rod+ shell bearings, piston being piston+gudgeon pin+1 circlip:
1. 569+549 = 1118
2. 568+546 = 1115
3. 567+549 = 1114
4. 567+551 = 1118
They look pretty good, but the kitchen scales I used aren't giving consistent results, so these values were the result of a number of weighings, being sure to repeat the positioning on the scale. They are all as pulled from the case, no cleaning, so this was the actual rotating mass, ignoring oil in the rod.
1981 RHD 2.0 Aircooled Leisuredrive project, CU engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
1990 RHD 1.9 Auto Sleeper with DF/DG engine
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
Its not that then.
Personally I wouldn't worry as you are fitting new shells
Personally I wouldn't worry as you are fitting new shells
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
937carrera wrote:
I still want to figure out why there is a dimension difference between the two bearings, but that's just satisfying my intellectual curiosity.
I know
The answer is staring you in the face, let's see if you can work it out before I can get into the shed and get the money shot.
- itchyfeet
- Registered user
- Posts: 12427
- Joined: 23 Jul 2007, 17:24
- 80-90 Mem No: 12733
- Location: South Hampshire
Re: WBX-Unknown
- bigbadbob76
- Registered user
- Posts: 1733
- Joined: 07 Nov 2016, 14:41
- 80-90 Mem No: 15707
- Location: Isle of Skye
Re: WBX-Unknown
Doh!
Obvious now aint it.
Obvious now aint it.
'86 1.9 DG, 4 spd, tintop, camper conversion.
Split case club member.
Split case club member.